********************************************************************************
SMCIPMITool v1.7.0 09/13/2010
Copyright(c) 2010 by Super Micro Computer, Inc. http://supermicro.com/
********************************************************************************
========
1.Readme
========
SMCIPMITool is a command line interface utility for the Supermicro SuperBlade
and IPMI device.
=====================
2.Setup and Execution
=====================
This utility needs Sun JRE 1.5.x or above. Please install Sun Java in your
platform in advance. To download, please go to following link:
http://java.sun.com/javase/downloads/index.jsp
There are 2 executable files in the SMCIPMITool utility.
1.SMCIPMITool.jar : A jar file only.
2.SMCIPMITool.exe : A windows executable wrapper for SMCIPMITool.jar
User can choose the jar or a native executable file. For Linux environment,
It needs an extra setting to the environment, as shown below.
Add jre to your PATH line in .bashrc file
PATH=/usr/java/jre1.5.0_12/bin:$PATH
The "jre1.5.0_12" folder may change depending on your version of java.
===================
3.Usage and Command
===================
In the console mode, please run the following command to start. There will be
on-line help included.
Usage:
java -jar SMCIPMITool.jar <IP> <username> <password> [commands ... ]
or
SMCIPMITool.exe <IP> <username> <password> [commands ... ]
Following are all commands for SMCIPMITool.
Command: Main available commands
Command(s):
system(sys) System status overview
failure(fail) Blade system failure report
blade(bl) Server blade management
gigabit(gb) Gigabit switch management
power(ps) Power supply management
ib Infiniband management
cmm CMM management
listtemp(lst) List system temperatures
sel System event log
allsel <filename> All Blade SEL to CSV (OEM)
user User management
vm Virtual Media management
ipmi IPMI device management
ver Print version
ch Change managed device in shell mode
list [keyword] List all or find available commands
find [<Start> <End> <netMask>] Find IPMI device from local or IP range
found [clear] List or clear found IPMI devices
exec <filename> [loop] [delay] Execute commands from file
host Host management
hostrun <host|group> <command> Run a command on host or group
trap IPMI SNMP Trap receiver management
sc Execute DOS/Linux shell command
pminfo [<busId> <SlaveAddr>] PMBus health
nm Node Management
kvmwa SIM(WA) KVM console (graphic mode)
ukvm KVM launcher (CMM,SIM,SIM(W),SIM(WA))
dr Drive redirection
kvm Open KVM console (graphic mode)
kvmw SIM(W) KVM console (graphic mode)
vmw SIM(W) Virtual Media
sol SOL Commands
===========
4.Examples
===========
D:\>SMCIPMITool 192.168.1.112 ADMIN ADMIN system
Blade Module (10/10)
--------------------
Blade | Power | KVM | UID | Error | BMC | Watt
----- | ----- | --- | --- | ----- | --- | ----
Blade 1 | On | | | | Yes | 300W
Blade 2 | On | | | | | 300W
Blade 3 | On | | | | Yes | 300W
Blade 4 | On | | | | Yes | 375W
Blade 5 | On | | | | Yes | 300W
Blade 6 | On | | | | | 300W
Blade 7 | On | Selected | | | Yes | 300W
Blade 8 | On | | | | Yes | 300W
Blade 9 | On | | | | Yes | 300W
Blade 10 | On | | | | Yes | 300W
Gigabit SW Module (1/2)
------------------------
GBSW | Power | Error | Init | Switch | 2.5V | 1.25V
---- | ----- | ----- | ---- | ------ | ---- | -----
GBSW 1 | On | | OK | 37C/99F | 2.512V | 1.2V
Power Supply Module (4/4)
--------------------------
PS | Power | Fan 1 | Fan 2 | Temp. | Watts | DC | AC | F/W | FRU
-- | ----- | ----- | ----- | ----- | ----- | -- | -- | --- | ---
PS 1 | On | 6183 | 6068 | 38C/100F | 2000 | N/A | N/A | 2.6 | 01
PS 2 | On | 6183 | 6183 | 38C/100F | 2000 | N/A | N/A | 2.6 | 01
PS 3 | On | 6068 | 6068 | 39C/102F | 2000 | N/A | N/A | 2.6 | 01
PS 4 | On | 6068 | 6068 | 41C/106F | 2000 | N/A | N/A | 2.6 | 01
Infiniband Module (1/2)
------------------------
IB | Power | Init | VVDD | 3.3V Aux | 1.2V | 1.8V | 3.3V | Temp.
-- | ----- | ---- | ---- | -------- | ---- | ---- | ---- | -----
IB 1 | On | OK | 1.52V | 3.31V | 1.19V | 1.74V | 3.31V | 34C/93F
CMM Module(1/2)
----------------
CMM | M/S | Status
--- | --- | ------
CMM 1 | Master | OK
D:\>SMCIPMITool 192.168.1.238 ADMIN ADMIN blade 1 sensors
Status | Sensor | Reading | Low Limit | High Limit |
------ | ------ | ------- | --------- | ---------- |
OK | CPU1 Temp. | 50C/122F | N/A | 80C/176F |
OK | CPU2 Temp. | 43C/109F | N/A | 80C/176F |
OK | CPU3 Temp. | 47C/117F | N/A | 80C/176F |
OK | CPU4 Temp. | 46C/115F | N/A | 80C/176F |
OK | System Temp. | 43C/109F | N/A | 75C/167F |
OK | CPU1 Voltage | 1.34 V | 0.92 V | 1.5 V |
OK | CPU2 Voltage | 1.32 V | 0.92 V | 1.5 V |
OK | CPU3 Voltage | 1.23 V | 0.92 V | 1.5 V |
OK | CPU4 Voltage | 1.29 V | 0.92 V | 1.5 V |
OK | 1.2V | 1.19 V | 1.08 V | 1.32 V |
OK | 3.3V | 3.18 V | 2.96 V | 3.63 V |
OK | 12V | 11.42 V | 10.75 V | 13.25 V |
OK | 5V | 4.92 V | 4.49 V | 5.5 V |
OK | 5VSB | 4.82 V | 4.49 V | 5.5 V |
OK | Battery | 3.05 V | 2.96 V | 3.63 V |
Shell mode example
D:\>SMCIPMITool 192.168.1.238 ADMIN ADMIN shell
Press Ctrl+D or "exit" to exit
Press "?" or "help" for help
Press TAB for command completion
Press UP and DOWN key for command history
CMM>blade status
Blade Module (5/10)
--------------------
Blade | Power | KVM | UID | Error | BMC | Watt
----- | ----- | --- | --- | ----- | --- | ----
Blade 1 | On | | | | Yes | 500W
Blade 4 | On | | | | Yes | 475W
Blade 6 | On | | | | Yes | 200W
Blade 8 | On | | | | Yes | 175W
Blade 10 | On | Selected | | | Yes | 475W
CMM>vm iso 1 192.168.10.43 iso cd1.iso
done
CMM>vm status
Drive 1
Device Status = CD-ROM image on Windows share set
Image Size = 522766336 (bytes)
Access Mode = Read-Only
Image source = //192.168.10.43/iso/cd1.iso
Drive 2
Device Status = CD-ROM image on Windows share set
Image Size = 522766336 (byte)
Access Mode = Read-Only
Image source = //192.168.10.43/iso/cd1.iso
CMM>sel info
Total Entries: 256
SEL Version: 1.5
Free Space: 4096 bytes
Recent Entry Added: Pre-Init 00:00:00
Recent Entry Erased: Pre-Init 00:00:00
==============
5.Release note
==============
-------------------------------------------------------------------------------
Version 1.7.0 build 100913
-------------------------------------------------------------------------------
1. Added Deploymenet Utilities command
Command:deploy
Command(s):
one <ISO file> Deploy BIOS/FW for general Server
all <ISO file> Deploy BIOS/FW for SuperBlade
status Display current status of deployment process
clear clear and remove all Virtual Media session
2. Added 10G Switch support
3. Updated sensor type name to be "OEM" of 0xC0 sensor type. (HDD S.M.A.R.T and CPU Overheat)
4. Updated iKVM v1.63 r1
5. Added 20x 1GbE pass thru
-------------------------------------------------------------------------------
Version 1.6.3(beta) build 100903
-------------------------------------------------------------------------------
1.Internal released
-------------------------------------------------------------------------------
Version 1.6.2 build 100720
-------------------------------------------------------------------------------
1. Added command "kvmwa" for SIM(WA) KVM in graphics mode
2. Added command "ukvm" for launch CMM,SIMBL,SIM,SIM(W) and SIM(WA) automatically
3. Added "allsel <filename>" command for convert all blade sel to csv file
4. Added "sel csv" command for save SEL as csv file
5. Added FRU File ID field in board and Product info
6. Fixed X8DTG SDR missing issue(X8DTG-DF Rev 1.3/2.00 ,AMI firmware)
-------------------------------------------------------------------------------
Version 1.6.1 build 100510
-------------------------------------------------------------------------------
1. Updated FRU display function
(Ability to show Internal use area, MultiRecord area, OEM custom field)
2. Added B8DTP, B8DT6_OEM, B8DTT_OEM for blade system
3. Updated SMART failure SEL (DISK 0 failure cannot be displayed)
4. Updated conversion formula for PMBus information.
5. Updated high&low limit refer to non-critical value in the sensor command
6. Fixed overflow of low limit of temperature
7. Added CPU overheat SEL for ATEN FW
8. Fxied bug of event log for memory ECC error
9. Remove SMCIPMITool-linux due to unhandled problem.
Use java -jar SMCIPMITool.jar instead
-------------------------------------------------------------------------------
Version 1.6.0 build 100223
-------------------------------------------------------------------------------
1.Support Node Manager commands. (Commands to ME)
Available command(s):
detect detect if ME presented
ver Node Manager version
cap Node Manager capabilities
status [enable|disable] Enable/Disable Node Manager
stat [id] Get power statistics(or by PolicyId)
resetStat [id] Reset power statistics(or by PolicyId)
pstate [value] Get/Set P-State
tstate [value] Get/Set T-State
ptstate Show P-State and T-State
alert [dest] Get/Set alert destination (See LAN Config)
scanPolicy [end] Scan Policy
addPolicy <id> <limit> <t> <p> Add Policy
delPolicy <id> Delete Policy
getPolicy <id> Get Policy
enablePolicy <id> Enable Policy
disablePolicy <id> Disable Policy
Examples:
1.Detect if Node Manager supported
Example:
SIM(WA)>nm detect
This device supports Node Manager
2.Node Manager version
Example:
SIM(WA)>nm ver
Node Manager Version = 1.5
Firmware Version = 1.05
3.Node Manager capabilities
Example:
SIM(WA)>nm cap
Max concurrent settings = 10
Max Power limit value = 32767 w
Min Power limit value = 0 w
Max Correction Time settable = 600000 ms
Min Correction Time settable = 6000 ms
Max Statistics Reporting period = 3600 s
Min Statistics Reporting period = 1 s
Limiting type = CPU power limiting
Limiting based on = Wall input power. PSU input power
4.Node Manager status
Example:
SIM(WA)>nm status
Node Manager is enabled
5.Node Manager statistic
Example:
SIM(WA)>nm stat
Gloabal Power statistic
Current = 209 w
Minimum = 128 w
Maximum = 255 w
Average = 166 w
Time = 02/23/2010 11:11:27 TUE
Reporting Period = 1 sec
Node Manager is enabled
Measurements in progress
6.Node Manager statistic with Policy ID
Example:
SIM(WA)>nm stat 11
Policy Id = 11
Current = 209 w
Minimum = 209 w
Maximum = 210 w
Average = 209 w
Time = 02/23/2010 11:12:19 星期二
Reporting Period = 60 sec
Policy is not enabled
Measurements in progress
7.Show P-State & T-State
Example:
SIM(WA)>nm ptstate
P-State : High |#______________| Low [0/15] (Current/Number of State)
T-State : High |#_______| Low [0/8] (Current/Number of State)
8.Add Policy ( addPolicy <id> <limit> <correction time(ms)> <report period(s)> )
This command create a policy with following parameters.
Policy id = 15
power limit = 150w
correction time = 60000 ms
report period = 10 s
Example:
SIM(WA)>nm addPolicy 15 150 60000 10
Done
9.Get Policy
Example:
SIM(WA)>nm getPolicy 15
Power Limit = 150 w
Correction Time limit = 60000 ms
Statistics Reporting Period = 10 s
Policy state:
Policy enabled
Per Domain Node Manager policy control enabled
Global Node Manager policy control enabled
Policy Exception action state:
Send alert
10.Alert setting
Check "ipmi lan snmp" command to determine which lan destination to send Node Manager alert. The alert will
be sent by Node Manager
Example:
SIM(WA)>ipmi lan snmp
Seq IP MAC
--- -- ---
1 0.0.0.0 00:00:00:00:00:00
2 192.168.12.150 00:00:00:00:00:00
3 0.0.0.0 00:00:00:00:00:00
4 0.0.0.0 00:00:00:00:00:00
5 0.0.0.0 00:00:00:00:00:00
6 0.0.0.0 00:00:00:00:00:00
7 0.0.0.0 00:00:00:00:00:00
8 0.0.0.0 00:00:00:00:00:00
9 0.0.0.0 00:00:00:00:00:00
10 0.0.0.0 00:00:00:00:00:00
11 0.0.0.0 00:00:00:00:00:00
12 0.0.0.0 00:00:00:00:00:00
13 0.0.0.0 00:00:00:00:00:00
14 0.0.0.0 00:00:00:00:00:00
15 0.0.0.0 00:00:00:00:00:00
SIM(WA)>nm alert 2
Done
SIM(WA)>nm alert
Destionation selector = 2
11.Node Manager alert sent from ME
Example:
SIM(WA) [!Trap(1)]>trap list
-------------------------------------------------------------------------
Trap (1)
Sender = 192.168.12.161
Community = public
Sensor = Node Manager Alert Threshold Exceeded Sensor
Local Time Stamp = 2010/02/23 11:15:53 星期二
Description :
Event Dir : Assertion
Event Type : 72h
Policy event : Threshold exceeded
Threshold Index : 0
Policy ID = 15
12.Check Power Supply status
Example:
SIM(WA)>pminfo
[SlaveAddress = 78h]
Item | Value
---- | -----
Status |
AC Input Voltage | 101.0 V
AC Input Current | 1.17 A
DC 12V Output Voltage | 12.08 V
DC 12V Output Current | 8.12 A
Temperature 1 | 17C/63F
Temperature 2 | 33C/91F
Fan 1 | 9389 RPM
DC 12V Output Power | 98 W
AC Input Power | 111 W
PMBus Revision | 0x0001
PWS Serial Number | 0000DH109100009
PWS Module Number | PWS-721P-1R
PWS Revision | REV1.0
-------------------------------------------------------------------------------
Version 1.5.9 build 100212
-------------------------------------------------------------------------------
1. Updated formula for pmInfo command
2. Fixed delsdr command cannot delete if SDR ID more then 3 chars
-------------------------------------------------------------------------------
Version 1.5.8 build 100104
-------------------------------------------------------------------------------
1. Added TwinBlade supported
2. Added B8DTT supported
-------------------------------------------------------------------------------
Version 1.5.7 build 091009
-------------------------------------------------------------------------------
1. Added IBQDR
2. Updated BHQIE sensors' formula
-------------------------------------------------------------------------------
Version 1.5.6 build 090810
-------------------------------------------------------------------------------
1.Rebuild from 1.5.5. Fixed the missed files.
-------------------------------------------------------------------------------
Version 1.5.5 build 090804
-------------------------------------------------------------------------------
1. Added assertion and deassertion type in trap receiver
2. Updated pmInfo command for supporting {0xb0,0x78,0x7a,0x7c,0x7e} slave address
3. Updated pmInfo command (fomula of power watts)
4. Added B8DTL-E and B8DTL-L
5. Updated PEF table for ATEN's fw
6. Fixed a bug that cannot receive trap which send by ATEN's fw
7. Added delete sdr command
Command: delsdr <SDR record ID> Delete SDR
ex:delsdr 10
8. Added BHQIE sensor's table
-------------------------------------------------------------------------------
Version 1.5.4 build 090601
-------------------------------------------------------------------------------
1. Added PMBus command for getting power supply health info
pminfo [<busId> <SlaveAddr>] PMBus health
Example:
SIMBL>pminfo
Item | Value
---- | -----
Status | [Status OK]
AC Input Voltage | 97.5 V
AC Input Current | 1.43 A
DC 12V Output Voltage | 12.09 V
DC 12V Output Current | 9.5 A
Temperature 1 | 33C/91F
Temperature 2 | 38C/100F
Fan 1 | 9847 RPM
DC 12V Output Power | 114 W
AC Input Power | 133 W
PMBus Revision | 0x0001
PWS Serial Number | P7211C914IT0835
PWS Module Number | PWS-721P-1R
PWS Revision | REV1.0
2. Updated memory ecc SEL for X8 series board
-------------------------------------------------------------------------------
Version 1.5.3 build 090420
-------------------------------------------------------------------------------
1. Updated Blade HW configuration
2. Updated B8DT6/E sensor's table
3. Added SEL event for CPU temp overheat
4. Added B8DT6/E sensor's table
5. Updated SNMP setting for AMI's new FW update
6. Added IPMB raw command for KIRA and Winbond
-------------------------------------------------------------------------------
Version 1.5.2 build 090302
-------------------------------------------------------------------------------
1. Updated SNMP setting for AMI's new FW update
2. Added IPMB raw command for KIRA and Winbond
3. Added UID function for AMI
4. Added sensor number in IPMI sensor command
-------------------------------------------------------------------------------
Version 1.5.1 build 090204
-------------------------------------------------------------------------------
1. Added more info for ECC and PCI error SEL event
2. Added DHCP command into CMM cmd category
-------------------------------------------------------------------------------
Version 1.5.0 build 081231
-------------------------------------------------------------------------------
1. Added KVM,Virtul Media and Flash command for Hermon (SIMSOW)
a.PlugIn Command: "kvmw" for KVM Window mode
b.PlugIn Command: "vmw" for virtual Media
vmw floppy <image file> Floppy image as virtual media
vmw usbkey <drive letter> USB key as virutal media
vmw iso <ISO file> ISO file as virtual media
vmw cd <drive letter> CD/DVD drive as virutal media
vmw stopFloppy Stop connected floppy
vmw stopUsbkey Stop connected USBKey
vmw stopISO Stop connected ISO
vmw stopCD Stop connected CD/DVD
vmw status(st) Virtual Media status
c."ipmi flashw" command for Hermon fw flashing
2. Updated SNMP pef table for AMI in "ipmi lan snmp" command
3. Added SIMBL(W) guid
4. Updated SNMP Destination count
5. Added AMD CPU in the blade info (motherboard configuration)
Command list:
bl <blade Index> config
6. Fixed user ID cannot be deleted in AMI's fw
7. Fixed CPU not installed display error in AMI's fw
8. Renamed SuperBladeTool to SMCIPMITool. Since it supports both SuperBlade and IPMI products
9. Added B7DCL sensor table
-------------------------------------------------------------------------------
Version 1.04.13 build 080908
-------------------------------------------------------------------------------
1. Added 10G pass Thru management status in sys command
-------------------------------------------------------------------------------
Version 1.04.12 build 080812
-------------------------------------------------------------------------------
1. Updated winbond GUIDs. Includes both on-board and add-on types.
2. Updated the blade sensors threshold reading. The blade CPU and system threshold
temperature are read from BIOS setting.
3. Added new CPU text temperature status (low, medium, high and overheat status)
4. Added pulse diagnostic interrupt command
Command:
CMM>ipmi power diag
-------------------------------------------------------------------------------
Version 1.04.11 build 080718
-------------------------------------------------------------------------------
1. Added B7DC3-IB supported
2. Added motherboard configuration command
Command list:
bl <blade Index> config
CMM>bl 7 config
MB ID = B1
Pwr Consumption = 300W
CPUs = 1
CPU Type = Dempsey B1
CPU Speed = 3.00Ghz
DIMMs = 1
Memory Size = 1024MB
Memory Speed = 667Mhz
LANs = 2
LAN 1 MAC = 01:00:02:00:00:00
LAN 2 MAC = 01:00:02:00:00:01
-------------------------------------------------------------------------------
Version 1.04.10 build 080623
-------------------------------------------------------------------------------
1. Changed display of power supply watts (1400 -> 1400/1200) when power is off
2. SIMSO-W+ added
-------------------------------------------------------------------------------
Version 1.04.09 build 080613
-------------------------------------------------------------------------------
1. Changed display of power supply watts (1400 -> 1400/1200)
2. Added Office blade and Enterprise blade mode
-------------------------------------------------------------------------------
Version 1.04.07 build 080515
-------------------------------------------------------------------------------
1. Added retry mechanism for IPMB call. Make IPMB call more stable
-------------------------------------------------------------------------------
Version 1.04.06 build 080508
-------------------------------------------------------------------------------
1.Changed 1.8V to Memory Voltage and changed low limit to 1.34v.
2.Fixed a false alarm of cpu 2 core A temp and cpu2 core B temp.
It shows "CPU2 Core A Temp:Reading out of range" on fail command
when you install 2 CPUs with PECI feature.
-------------------------------------------------------------------------------
Version 1.04.05 build 080430
-------------------------------------------------------------------------------
1.Added function for setting SIMBL VLAN and DHCP function via IPMB from CMM
2.Added function for sending IPMI raw command via IPMB from CMM
Command:bl <blade_index> bmc
Available command(s):
ip [IP] Get/set BMC IP
dhcp [enable|disable] Enable/Disable DHCP
vlan [<enable|disable> <tag>] Display/Enable/Disable VLAN
ipmb <netFn> <cmd> [data] Send IPMI raw command. netFn<<2 is needed
3.Added DOS/Linux shell command supported.
Examples:
CMM>sc dir (execute dir command in Windows OS)
CMM>sc ls (execute ls command in Linux OS)
CMM>sc ping 192.168.10.123 (execute ping command)
-------------------------------------------------------------------------------
Version 1.04.04 build 080418
-------------------------------------------------------------------------------
1.Added Display/Enable/Disable VLAN command
ipmi lan vlan [<enable|disable> <VLAN tag>]
2.Added Get/Set SNMP community string command
ipmi lan snmpcomm [community string]
3.Added support for BHDME MB
-------------------------------------------------------------------------------
Version 1.04.03 build 080331
-------------------------------------------------------------------------------
1.Updated virtual media function for i2c lan type
-------------------------------------------------------------------------------
Version 1.04.02 build 080329
-------------------------------------------------------------------------------
1.Added configuration backup/restore/sync functions
Command list:
ipmi oem backup
ipmi oem restore
cmm 1(or 2) syncfg
2.Added "delay" command in the shell mode
3.Added a workround for B7DC3/B7DCE shows SIMBL is installed while it first
pluged into middle plane and powered off.
4.Updated B7DCE,H8DMT,B7DC3,X7SBT,X7SBU in "IPMI OEM ID" command
5.Updated power supply current. Dividing dc output current by 2.
6.Added checker for firmware which doesn't support virutal media
7.Fixed a minor bug in ch command. (Some variables are not cleared)
8.Set chunk size to 80 byte if lan type is share lan1 and lan driver is i2c for
firmware upload.
9.Changed the sensor name 1.2V to CPU VTT (Low/hight limit, 0.99/1.32) in Intel
blade sensor table.
10.Fixed GBSW dispaly power on while the power supply is turned off
-------------------------------------------------------------------------------
Version 1.04.01 build 080125
-------------------------------------------------------------------------------
1.Added tab-completion function like bsh or windows command pormpt
2.Added function that persistence command history. Command History
will restore when re-enter shell mode. (Use the Jline)
Set history in the SMCIPMITool.properties
history = on|off
if history = on, the all the command history will be save to file and
restore when next shell mode.
3.Added firmware flash command for SIMXX IPMI
4.Define command return code in Command class.
sub Commands can define their own command return code.
Script program knows the command result form the command return code.
5.Updated CMM NTP time set function
6.Updated ch command to accpet ".192" type. Not only accept "*.192".
-------------------------------------------------------------------------------
Version 1.03.04 build 080118
-------------------------------------------------------------------------------
1.Add Command History available in Linux terminal. Pressing up or down key to
go through command history. This is completed by adding Jline open source project
Note: For SOL function work properly, SOL PlugIn(sol related functions) should
use this version.
-------------------------------------------------------------------------------
Version 1.03.03 build 080109
-------------------------------------------------------------------------------
1.Added a checker to check the SEL and SDR mismatch problem
2.Added 14 blades Supported
3.Added 'help' command in the exec mode. (help observe the run time information)
4.Fixed some trap function bugs. (File close, parameter validation)
5.Update trap reciever for blade snmp
-------------------------------------------------------------------------------
Version 1.03.02 build 071128
-------------------------------------------------------------------------------
1.Added PlugIn mechanism.
2.Updated the gb pass thru initialized display error
3.Added Virtual Media supported for general SIM IPMI
-------------------------------------------------------------------------------
Version 1.03.01 build 071126
-------------------------------------------------------------------------------
1.Added cmm NTP fucntion.
command:ntp <UTC offset> <NTP1> [NTP2] Sync time with NTP servers
2.Added Trap receive function in shell mode.
Command:trap
Available command(s):
start Strat Trap receiver
stop Stop Trap receiver
status(st) Trap receiver status
list List the received Traps
clear Clear the received Traps
save Save the received Traps to file
savepet Save as the IPMIView TrapReceiver PET format
*Set trap receive in the SuperBladeTool.properties
trap = on|off
if trap = on, then trap receive will be started when enter to shell mode
3.Added reading and threshold in SEL
4.Fixed the sensor name display error in the SEL list
5.Added keyword function in list command
6.Added record function. set "reocrd" field in the SuperBladeTool.properties.
*Set record in the SuperBladeTool.properties
record = on|off
if record = on, the all the content of shell mode will be record to file
8.Fixed a bug that GB Switch initilized field display error on SuperBladeTool
-------------------------------------------------------------------------------
Version 1.02.01 build 071105
-------------------------------------------------------------------------------
1.Added exec command for executing commands from a file
(Command: exec <filename> [loop] [delay])
2.Added all("*") and comma separater for multiple execution on blade, gigabit,
power, ib commands. (see example 2)
3.Added host and group data management. A host.properties file will be created.
4.Added hostrun command. for running a command on a host or a group (see example 1)
5.Imporved command list information.
6.Fixed a bug that no prompt when connect to OSA IPMI
Examples:
1.host and hostrun command:
CMM>host list
Host:
Host IP
---- --
1.112 (192.168.1.112)
1.119 (192.168.1.119)
bl1 (192.168.10.243)
bl2 (192.168.10.244)
Host Group:
Group Name Host
---------- ----
1 1.112
1.119
bl bl1
bl2
CMM>hostrun bl ipmi power up
[bl1:192.168.10.243]
Done
[bl2:192.168.10.244]
Done
2."*" and comma separater support for blade commands:
CMM>bl 3,7,10 uid on
[ 3]:
Done
[ 7]:
Done
[10]:
Done
CMM>bl * power on
[ 1]:
Blade 1 is not present
[ 2]:
Blade 2 is not present
[ 3]:
Done
[ 4]:
Blade 4 is not present
[ 5]:
Blade 5 is not present
[ 6]:
Blade 6 is not present
[ 7]:
Done
[ 8]:
Blade 8 is not present
[ 9]:
Blade 9 is not present
[10]:
Done
-------------------------------------------------------------------------------
Version 1.01.02 build 071022
-------------------------------------------------------------------------------
1.Added FOUND [clear] sub command and information of last update.
2.Added IPMI oem command
2.1 Added clear chassis intrusion command (command: ipmi oem clrint)
2.2 Added id command for showing MB ID (command: ipmi oem id)
2.3 Added id name command for showing MB name (Command: ipmi oem id name)
3.Fixed a bug that impi raw command cannot accpet the prameter which the msb=1
4.Added listtemp command for showing all the blade system temp
example:
CMM>lst
Status | Module | Sensor | Reading | High Limit |
------ | ------ | ------ | ------- | ---------- |
OK | Blade 1 | CPU1 | 29C/ 84F | 80C/176F |
OK | Blade 1 | CPU2 | 29C/ 84F | 80C/176F |
OK | Blade 1 | System Temp. | 33C/ 91F | 75C/167F |
OK | Blade 2 | CPU1 | 28C/ 82F | 80C/176F |
OK | Blade 2 | CPU2 | 28C/ 82F | 80C/176F |
OK | Blade 2 | System Temp. | 33C/ 91F | 75C/167F |
OK | Blade 7 | CPU1 Core A Temp. | 49C/120F | 80C/176F |
OK | Blade 7 | CPU1 Core B Temp. | 46C/115F | 80C/176F |
| Blade 7 | CPU2 Core A Temp. | n/a | 80C/176F |
| Blade 7 | CPU2 Core B Temp. | n/a | 80C/176F |
OK | Power 1 | Temp. | 40C/104F | 85C/185F |
OK | Power 2 | Temp. | 40C/104F | 85C/185F |
OK | Power 3 | Temp. | 39C/102F | 85C/185F |
OK | Power 4 | Temp. | 40C/104F | 85C/185F |
OK | GBSW 1 | Switch | 41C/106F | 80C/176F |
-------------------------------------------------------------------------------
Version 1.01.01 build 071016
-------------------------------------------------------------------------------
1.Add FIND command for disocver IPMI device
2.Add FOUND command for list the found IPMI device
3.update history command execution. use \<#>
4.add IPMI command group
sensor(sr) Sensor status
power Power control
acpi ACPI status
lan LAN configruation
fru FRU information
reset reset BMC
ver IPMI device version
raw <netFn> <cmd> [data] Send IPMI raw command. netFn needs shift 2 bit
Sub Command for lan
ip [ip] get/set IP. Format:###.###.###.###
mac [mac] get/set MAC. Format:##:##:##:##:##:##
gateway [gateway_IP] get/set gateway. Format:###.###.###.###
netmask [netmask] get/set netmask. Format:###.###.###.###
snmp [<seq> <ip> [mac]] get/set SNMP destination
arp [on|off] on/off Gratuitous ARP
dhcp [enable|disable] enable/disable DHCP
5.fixed "No enough power" message failed.
6.fixed if out put DC power over 130A shows wrong value. It's overflow
7.added short string command instead of long characters typing.
8.added CMM IP address info in the "cmm status" command
9.reduced the number of concurrent connections during the command execution.
-------------------------------------------------------------------------------
Version 1.00.06 build 071005
-------------------------------------------------------------------------------
1.add slave CMM check. Only cmm,sel and user functions are available for slave CMM
2.minor information display changed.
-------------------------------------------------------------------------------
Version 1.00.05 build 070918
-------------------------------------------------------------------------------
1.Added command history function. press "\" and "/" for executing and displaying
command history.
2.Added "list" command. Print all available commands
3.Added get/set mac address command in cmm.
4.Updated SEL list message.
5.Added more information in help command (press "?" or "help" in shell mode).
6.Added blade power status in the blade power command.
7.Added cmm connected info for "cmm status" or "cmm # status" command.
8.Added wild card for ch command. Made it easier to change managed cmm ip.
ex:
case 1, 192.168.100.118 change to 192.168.100.9
CMM>ch *.9
case 2, 192.168.100,1 change to 192.168.1.10
CMM>ch *.1.10
-------------------------------------------------------------------------------
Version 1.00.04 build 070908
-------------------------------------------------------------------------------
1.Fixed a DC current negative bug.
2.Updated Fan control command as 1,2,3,4 and auto. auto is automatic fan control.
3.Added ch command in shell mode used for changing IP [username] [password].
4.Changed prompt from "=>" to "CMM>"
-------------------------------------------------------------------------------
Version 1.00.03 build 070831
-------------------------------------------------------------------------------
1.Fixed a parsing bug in shell mode:
when giving the "blade" then "ver" command, it still shows blade available command.
It should execute "ver" command.
-------------------------------------------------------------------------------
Version 1.00.02 build 070830
-------------------------------------------------------------------------------
1.Fixed a problem of taking a long time when running under Linux OS.
The root cause was the secure random algorithm taking a long time.
This issue doesn't happen in Windows OS.
Verified in the following Java Linux versions:
a.jre 1.5.0_11 (FC4)
b.jre 1.6.0_02 (FC6)
jre1.*.* should match your jre version.
-------------------------------------------------------------------------------
Version 1.00.01 build 070823
-------------------------------------------------------------------------------
1.Fixed a bug that created a parse command error in shell mode.
2.Fixed a bug that prevented cmm date/time being set in shell mode.
3.Added ver command.
4.Add runtime info for help command in shell mode.
5.Some minor updates.
-------------------------------------------------------------------------------
Version 1.0 build 070822
-------------------------------------------------------------------------------
1.First Release
==============
6.JLine
==============
SMCIPMITool use jline for command history and tab-completion.
JLine is a Java library for handling console input. It is similar in functionality
to BSD editline and GNU readline. People familiar with the readline/editline
capabilities for modern shells (such as bash and tcsh) will find most of the command
editing features of JLine to be familiar.
For more information, please contact http://jline.sourceforge.net/index.html
===========================
7. Return code for CLI Mode
===========================
Following return code can be used in batch or script file.
STATUS_UNDEFINED = 144
STATUS_DONE = 0
STATUS_CONNECT_FAILED = 145
STATUS_LOGIN_FAILED = 146
STATUS_EXECUTE_PARAMETER_VALIDATE_FAILED = 147
STATUS_EXECUTE_EXCEPTION_OCCURRED = 148
STATUS_EXECUTE_FAILED = 149
STATUS_EXECUTE_ON_SLAVE_CMM_OR_UNAVAILABLE = 150
STATUS_EXECUTE_MODULE_NOT_PRESENT = 151
STATUS_EXECUTE_ONLY_FOR_CMM_CONNECTED = 152
STATUS_EXECUTE_NOT_SUPPORTED_DEVICE = 153
STATUS_COMMAND_NOT_FOUND = 180
STATUS_COMMAND_IP_FORMAT_ERROR = 181
STATUS_COMMAND_PARAMETER_LENGTH_INVALID = 182
STATUS_RESULT_NOT_ENOUGH_POWER = 215