#######################################################################
SuperMicro Switch Firmware Release 1.0.20-1
#######################################################################
Date: March 13th, 2020
#######################################################################
Products Related
#######################################################################
This firmware is applicable for the following switch products.
SBM-GEM-X2C, SBM-GEM-X2C+, SSE-G24-TG4, SSE-G48-TG4, SBM-GEM-X3S
#######################################################################
Recommendation
#######################################################################
This is the GA firmware release version.
We recommend strongly to upgrade to this firmware version.
#######################################################################
Improvements
#######################################################################
Resolved issues in release 1.0.20-1:
------------------------------------
1. Upgraded ssh version to 7.2 and ssl version to OpenSSL 1.0.2g.
2. Enabled more ciphers including AES128
#######################################################################
FIRMWARE UPGRADE PROCEDURE
#######################################################################
File Download
-------------
Download the bin file SWITCH_FIRMWARE_1.0.20-1.bin from Supermicro website below link
ftp://ftp.supermicro.com/Firmware/Switch/SBM-GEM-X2C_SSE-G24-TG4_SSE-G48-TG4/Release-1.0.20-1
Filename: SWITCH_FIRMWARE_1.0.20-1.bin - size 11,703,484 bytes
##################################################################################################
Please Note:
1. If your switch is running on firmware version 1.0.9 or earlier (for e.g. 1.0.7 or 1.0.7-7),
after upgrading to this firmware version, the saved configuration file restore will not work
for a few configurations. Hence we strongly recommend manual reconfiguration of all your configs
after upgrading the firmware. Please take copy of "show running-config" command output before
upgrading to this firmware. And after upgrading, please reconfigure the switch based on your
earlier configurations.
##################################################################################################
Steps to upgrade
================
Firmware Upgrade Procedure for CLI
----------------------------------
Make sure TFTP server is running on the system where firmware file is available.
Upgrade the firmware from CLI using the below command:
firmware upgrade tftp://<ip-address>/SWITCH_FIRMWARE_1.0.20-1.bin flash:normal
For <ip-address> in command, use the IP address of the TFTP server system where firmware file is avilable.
Firmware Upgrade Procedure for Web GUI
--------------------------------------
Firmware can be upgraded from Web GUI in System Management --> Firmware Upgrade web page.
Browse and select firmware image file and click on "Upload Firmware" button.
Web GUI firmware update does not require TFTP server.
#######################################################################
OTHER INFORMATION
#######################################################################
#######################################################################
The information in this readme file has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify
any person or organization of the updates.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software
and documentation, is the property of Supermicro and/or its licensors, and is supplied only
under a license. Any use or reproduction of this product is not allowed, except as expressly
permitted by the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE
OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE,
OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of Santa Clara
shall be the exclusive venue for the resolution of any such disputes. Super Micro's total
liability for all claims will not exceed the price paid for the hardware product.
Copyright 2020 by SUPER MICRO COMPUTER INC.
All rights reserved.