 | |
 | MBD-X7DBP-i-B | | | | |
| | Form Factor | | | Dimensions | - 16.24" Length x 11.23" Width (41.25cm x 28.52cm)
| | | |
| | CPU | - Dual 771-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same
type below: - Quad-Core Intel®
Xeon®Processor
5400/5300 sequence
(Harpertown
/Clovertown processor)
up to 3.16 GHz - Dual-Core Intel®
Xeon®Processor 5200/5100/5000
sequence (Wolfdale
/Woodcrest/Dempsey processor) up to 3.40 GHz | | System Bus | - 1333 / 1066 / 667 MHz system bus
| | Operating System Software | - Supports 64-bit Operating Systems
- Supports 32-bit Operating Systems
| | | |
| | Memory Capacity | - Eight 240-pin DIMM sockets
- Supports up to 32 GB 667/533MHz FB-DIMM memory
- Dual branch memory bus
- Memory must be populated in pairs
| | Memory Type | - 667/533MHz FB-DIMM (Fully Buffered DIMM) ECC SDRAM 72-bit, 240-pin gold-plated DIMMs
| | DIMM Sizes | | | Memory Voltage | | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 Single Device Data Correction (SDDC)
| | | |
| | Chipset | - Intel® 5000P (Blackford) chipset
- MCH + PXH + ESB2
| | SATA | - ESB2 SATA Controller
- RAID 0, 1, 5, 10 support (Windows Only)
- RAID 0, 1, 10 support (Linux)
| | IPMI | | | Network Controllers | - Intel® (ESB2/Gilgal) 82563EB Dual-Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT support for fast, scaleable, and reliable networking
| | Graphics | - ATI ES1000 controller with 16 MB of video memory
| | Super I/O | | | Clock Generator | | | | |
| | Serial ATA | - Six Serial ATA ports
- Six SATA hard drives supported
| | IDE | - Single EIDE channel support up to two UDMA IDE devices
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
| | Floppy | - 1 Floppy controller; 1.44 MB
| | LAN | | | USB | - 2x USB rear ports
- 2x USB internal headers, 1 dual, 1 single
- USB 2.0 Compliant / 1.1 Compliant
| | VGA | | | Keyboard / Mouse | - PS/2 keyboard and mouse ports
| | Serial Port / Header | - 2 Fast UART 16550 serial ports
| | | | |
| | 1U Chassis | - CSE-816A-R700
- CSE-816A-700
| | Important Chassis Notes | - To ensure system stability, a 500W (minimum) ATX power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin are required] | | | |
| | Left Universal Slot | - 1 (x8) PCI-e slot OR
- 1x 64-bit 100MHz PCI-X (3.3V) slot
| | Right Universal Slot | - 1 (x8) PCI-e slot OR
- 1x 64-bit 133MHz PCI-X (3.3V) slot
| | IPMI | - 1 SIM1U Slot (IPMI 2.0)
(Supermicro Intelligent Management) | | | |
| | BIOS Type | - 8Mb Flash EEPROM with Phoenix® BIOS
| | BIOS Features | - Plug and Play (PnP)
- SMBIOS 2.3
- APM 1.2
- DMI 2.3
- PCI 2.2
- ACPI 1.0
- ACPI 1.0 (limited)
- USB Keyboard support
- Hardware BIOS Virus protection
| | | |
| | Software | - Optional IPMI (Intelligent Platform Management Interface) 2.0 / 1.5 - with Virtual Media 8
- Optional KVM over LAN & 3rd LAN Port
- SuperDoctor® III
- Watch Dog
- NMI
| | Power Configurations | - ACPI Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode for AC power recovery
- Internal/External modem remote ring-on
| | | |
| | Voltage | - Monitors for CPU Cores, +3.3V, +5V, ±12V, +5V Standby, VBAT
- CPU Core 5-Phase-switching voltage regulator with auto-sense from 0.86V-1.63V
| | FAN | - Total of ten proprietary fan headers for up to ten fans
- Ten fans with tachometer status monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x fan connectors
- I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
| | LED | - CPU / System Overheat LED
| | Other Features | - Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
| | | |
| Environmental Spec. | - Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
| | | |
| | FCC | - Passed to meet FCC standard requirement
| |
