 | |
 | | MBD-X8DTU-LN4F+ -B | | | | | | Form Factor | | | Dimensions | - 12.8" x 16.5" (32.5cm x 41.9cm)
| | | | | CPU | - Dual 1366-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Intel®
Xeon®Processor 5600 Series (Westmere) - Intel®
Xeon®Processor 5500 Series (Nehalem-EP) | | QPI | | | | | | Memory Capacity | - 18x 240-pin DIMM slots
- Supports up to 288GB 1333 / 1066 / 800MHz DDR3 ECC Registered memory
- Supports up to 48GB 1333 / 1066 / 800MHz DDR3 ECC / Non ECC Unbuffered memory
- Memory Mirroring supported
| | Memory Type | - 1333 / 1066 / 800MHz ECC Registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
| | DIMM Sizes | - 1GB, 2GB, 4GB , 8GB , 16GB
| | Memory Voltage | | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
| | Note: | This board does not support LRDIMM memory. | | | | | Chipset | - Intel® 5520 (Tylersburg) chipset
- ICH10R + IOH-36D
| | SATA | - Intel ICH10R SATA 3.0Gbps Controller
- RAID 0, 1, 5, 10 support (Windows)
- RAID 0, 1, 10 support (Linux)
| | IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Winbond® WPCM450 BMC
| | Network Controllers | - 2x Intel® 82576 Dual-Port Gigabit Ethernet Controllers (4 ports)
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT 3 support for fast, scaleable, and reliable networking
- VMDq support for better performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
| | Graphics | | | Super I/O | | | | | | Serial ATA | - Six Serial ATA ports
- Six SATA hard drives supported
| | LAN | - 4x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
| | USB | - 2x USB rear ports
- 1x USB on-board
- 5x USB internal headers
- Total 8 USB 2.0 Compliant
| | VGA | | | Keyboard / Mouse | - PS/2 keyboard and mouse ports
| | Serial Port / Header | - 1 Fast UART 16550 serial port
- 1 Fast UART 16550 serial header
| | | | | | Important Chassis Notes | - To support the new generation Intel® Xeon® processor-based motherboards, a Revision K chassis is recommended for most models. Please talk to your sales representative or follow the link for details.
| | | | | PCI-Express / PCI-X / UIO | Left Side - 1 (x16) PCI-E 2.0 + 1 PCI-E 2.0 x4 by riser card
Right Side - 1 (x8) PCI-E 2.0 + 1 PCI-E 2.0 x4 by riser card
- For 2U configuration, Please go to UIO Riser Cards page
| | | | | BIOS Type | - 32Mb SPI Flash EEPROM with AMI® BIOS
| | BIOS Features | - Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
| | | | | Software | - IPMI (Intelligent Platform Management Interface) v1.5 / 2.0 with KVM support
- SuperDoctor® III
| | Power Configurations | - ACPI / ACPM Power Management
| | | | | Voltage | - Monitors for CPU Cores, +1.8V, +3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, Memory, Chipset Voltages.
- 6-Phase-switching voltage regulator
| | FAN | - Total of eight fan headers supporting up to 8 fans
- Eight 4-pin fan headers
- 8x fans with tachometer status monitoring
- Support 3-pin fans (w/o speed control)
- Low noise fan speed control (4-pin fan only)
| | Temperature | - Monitoring for CPU and chassis environment
- Thermal Control for 8x fan connectors
- PECI
| | Other Features | - Chassis intrusion detection
- Chassis intrusion header
| | | |
| | Environmental Spec. | - Operating Temperature: 10° to 35° C (50° to 95°F)
- Non-operating Temperature: -40° to 70° C (-40° to 158° F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
| |
