 | |
 | | SKU | | | | | |
| | Form Factor | | | Dimensions | - 12" x 9.5 " (30.5cm x 24.0cm)
| | | |
| | CPU | - Single LGA775 (Prescott) ZIF Socket
- Supports an Intel® Pentium® 4 processor 6x0 or 5x0 sequence on 90nm process ONLY (800MHz FSB) or
- Supports an Intel® Celeron® processor with 256KB L2 Cache (533MHz FSB)
- Hyper-Threading (HT) enabled
| | System Bus | | | Operating System Software | | | | |
| | Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 4 GB DDR2 400 / 533MHz unbuffered ECC or Non-ECC memory
- Dual channel memory bus
- Memory must be populated in pairs
| | Memory Type | - DDR2 400 / 533MHz unbuffered ECC or Non-ECC SDRAM 72-bit, 240-pin gold-plated DIMMs
| | DIMM Sizes | - 256MB, 512MB, 1GB
- Unbuffered ECC / non-ECC DDR2
- Total 256MB to 4GB memory
| | Memory Voltage | | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
| | | |
| | Chipset | - Intel E7221 (Copper River) chipset
- ICH6R + FWH + BCM5721
| | Serial ATA | - Intel® ICH6R SATA controller
- RAID 0, 1, JBOD support
| | SCSI | - Adaptec AIC-7902 Controller
- Dual-Channel Ultra320 SCSI (Host RAID only supports 4 drives)
- Host RAID 0, 1, 10, JBOD support
| | RAID | - Support for Zero-Channel RAID
- Optional: (Card not included)
| | IPMI | | | Network Controllers | - 2x Broadcom BCM5721 Gigabit Ethernet Controllers
- Supports 10/100/1000BASE-T, RJ45 output
| | Graphics | - Onboard integrated server quality graphics in MCH
| | Super I/O | | | | |
| | Serial ATA | - Four Serial ATA ports
- Four SATA hard drives supported
| | IDE | - One EIDE channel supports up to two UDMA IDE devices
- Supports UDMA Mode 5, and ATA/100
| | Floppy | - 1 Floppy controller; 1.44 MB, 2.88 MB, 3-mode support
| | Infrared | | | LAN | | | USB | - 2x USB 2.0 / 1.1 ports
- 4x USB 2.0 / 1.1 header for 4x ports
| | VGA | | | Keyboard / Mouse | - PS/2 keyboard and mouse ports
| | Serial Ports | - 1x Fast UART 16550 serial ports
- 1x serial header
| | Parallel Port | - 1x ECP / EEP Parallel Port
| | | | | 1U | | | Important Note | - To ensure system stability, a 300W (minimum) ATX power supply [4-pin +12V AND (20 or 24-pin)] is required.
| | | |
| | PCI-Express | | | PCI-X | - 1x 64-bit 100MHz PCI-X (3.3V) slot
| | PCI | - 1x 32-bit 33MHz PCI (5V) slot
| | | |
| | BIOS Type | - 8Mb Flash EEPROM with AwardBIOS®
| | BIOS Features | - Plug and Play (PnP)
- PCI 2.2
- ACPI 1.0
- USB Keyboard support
| | | |
| | Software | - Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
| | Power Configurations | - ACPI/APM Power Management
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Keyboard Wakeup from Soft-Off
- Power-on mode control for AC power loss recovery
- Internal/External modem remote ring-on
| | | |
| | Voltage | - Monitors for CPU Cores, +1.8V, +3.3V, +5, ±12V, +5V Standby
- CPU Core 4-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
| | FAN | - Total of five 3-pin fan headers
- 5x fans with tachometer monitoring
- Status monitor with firmware / software speed control
- Support 3-pin fans
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal control for 5x fan connectors
- I2C temperature sensing logic
| | LED | - CPU / System Overheat LED
- +5V standby alert LED
| | Other Features | - Chassis intrusion detection
- Chassis intrusion header
| |
