 | |
 | | MBD-X9DRE-TF+ -O | - X9DRE-TF+ (Standard Retail Pack)
| | MBD-X9DRE-TF+ -B | | | | |
| | Form Factor | | | Dimensions | - 13.68" x 13" (34.7cm x 33cm)
| | | | | CPU | - Dual Socket R (LGA 2011)
- Intel® Xeon® processor E5-2600
and E5-2600 v2 family†
(up to 135W TDP **) | | Note | † BIOS version 3.0 or above is required | | Note | ** Motherboard supports this maximum TDP. Please verify your system can thermally support. | | Cache | | | System Bus | | | | | | Memory Capacity | - 24x 240-pin DDR3 DIMM slots
- Up to 1.5TB DDR3 ECC LRDIMM
- Up to 768GB DDR3 ECC RDIMM
- Up to 128GB DDR3 ECC/non-ECC UDIMM
| | Memory Type | - 1866/1600/1333/1066/800MHz* ECC DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
- Support ECC and non-ECC UDIMMs
* Maximum memory speed may be capped by CPU. Please verify that the chosen CPU can support desired memory speed. | | DIMM Sizes | - 32GB, 16GB, 8GB, 4GB, 2GB, 1GB,
64GB LRDIMM | | Memory Voltage | | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
| | | | | Chipset | | | SATA | - SATA 2.0 3Gb/s with RAID 0, 1, 5, 10
SATA 3.0 6Gb/s with RAID 0, 1, 5, 10 | | IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Nuvoton WPCM450 BMC
| | Network Controllers | - Intel® X540 Dual Port 10GBase-T
- Virtual Machine Device Queues reduce I/O overhead
- Supports 10GBase-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- 1x Realtek RTL8201N PHY (dedicated IPMI)
| | Video | - G200 (Nuvoton WPCM450 BMC with graphic controller)
| | Super I/O | | | | | | SATA | - 2 SATA 3.0 ports (6Gb/s)
- 4 SATA 2.0 ports (3Gb/s)
| | LAN | - 2 RJ45 10GBase-T ports
- 1 RJ45 Dedicated IPMI LAN port
| | USB | - 8 USB 2.0 ports total
(4 rear + 2 via header + 2 Type A) | | Video | | | Serial Port / Header | - 2 Fast UART 16550 ports: 1 rear and 1 header
| | DOM | - 1 DOM (Disk on Module) power connector
| | TPM | | | | | |
| | 2U Chassis | - CSE-826BA-R1K28LPB
- CSE-826BA-R920LPB
- CSE-826BE16-R1K28LPB
- CSE-826BE16-R920LPB
- CSE-826BE26-R1K28LPB
- CSE-826BE26-R920LPB
| | 3U Chassis | | | Important Chassis Notes | - To support the new generation Intel® Xeon® processor-based motherboards, Revision M chassis is recommended. Please talk to your sales representative for details.
| |
| | |
| | PCI-Express | - 2 (x16) PCI-E 3.0 slots
- 4 (x8) PCI-E 3.0 slots
(Both CPUs need to be installed for full access to PCI-E slots and onboard controllers. See manual block diagram for details.) | | | | | BIOS Type | - 128Mb SPI Flash EEPROM with AMI BIOS
| | BIOS Features | - Plug and Play (PnP)
- APM 1.2
- PCI 2.3
- ACPI 1.0 / 2.0 / 3.0 / 4.0
- USB Keyboard support
- SMBIOS 2.7.1
- UEFI 2.3.1
| | | | | Software | - IPMI (Intelligent Platform Management Interface) v1.5 / 2.0 with KVM support
- SuperDoctor® III
- Watch Dog
- NMI
- Optional IPMI 1.5 / 2.0
| | Power Configurations | - ACPI / APM Power Management
- Main Switch Override Mechanism
- CPU Fan auto-off in sleep mode
- Power-on mode for AC power recovery
| | | | | Voltage | - Monitors for CPU Cores, +1.8V, +3.3V, +5V, ±12V, +3.3V Standby, +5V Standby, VBAT, HT, Memory, Chipset Voltages.
- 5 Phase-switching voltage regulator
| | FAN | - 9x 4-pin fan headers (up to 9 fans)
- 9x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 9x Fan Connectors
- I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
| | LED | - CPU / System Overheat LED
| | Other Features | - Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
| | | | |
| | Operating Temperature Range | - 10°C - 35°C (50°F - 95°F)
| | Non-Operating Temperature Range | - -40°C - 70°C (-40°F - 158°F)
| | Operating Relative Humidity Range | - 8% - 90% (non-condensing)
| | Non-Operating Relative Humidity Range | - 5% - 95% (non-condensing)
| |
