 | |
 | | MBD-H8DMU+-O | - H8DMU+ (Standard Retail Pack)
| | MBD-H8DMU+-B | | | | |
| | Form Factor | | | Dimensions | - 12.1" x 13" (30.7cm x 33.2cm)
| | | | | CPU | - Dual 1207-pin Socket F
- Supports up to two Six-Core / Quad-Core / Dual-Core AMD Opteron™ 2000 Series processors
- HT3.0 Link support ^
| | | - Two Hyper-Transport links between the CPUs
| | Chipset | | | | |
| | Memory Capacity | - Sixteen 240-pin DIMM sockets
- Supports up to 128GB DDR2 800/667/533 MHz memory *
- For Dual CPUs: Recommended that memory be populated equally in adjacent memory banks
- Dual channel memory bus
| | Memory Type | - DDR2 800/667/533 MHz buffered (registered) ECC SDRAM 72-bit, 240-pin gold-plated DIMMs
| | DIMM Sizes | - 256 MB, 512 MB, 1GB, 2GB, 4GB
| | Memory Voltage | | | | |
| | SATA | - nVidia MCP55 Pro SATA2 3.0Gbps Controller
- 6 SATA Ports
- nVidia Host RAID 2.0
- SATA RAID 0, 1, 0+1, 5, JBOD Support
| | IPMI | - Support for Intelligent Platform Management Interface v.2.0
- 200-pin IPMI slot (SIMSO)
- (Optional: AOC-SIMSO(+) R 3.00) **
- RMM (Remote Management Module)
- (Card not included)
- For dedicated LAN, CBL-0177L must be used on left full-size slot. (Cable not included)
| | Network Controllers | - nVidia MCP55 Pro Chipset Dual-port LAN / Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
| | VGA | - ATI ES1000 Graphics Controller
16MB Graphics & VGA port | | Super I/O | | | | |
| | SATA | | | IDE | - Single EIDE channel support up to two UDMA IDE devices
- Supports UDMA Mode 5
- Supports PIO Mode 4
- Supports ATA 100/133
| | Floppy | - 1 Floppy port; 1.44 MB support
| | LAN | | | USB | - FUCI
- Up to 6 USB Ports 2.0 Compliant
- 2 Rear Ports
- 4 Internal Headers
| | VGA | | | Keyboard / Mouse | - PS/2 keyboard and mouse ports
| | Serial Ports | - 1 Fast UART 16550 serial port
- 1 serial port header
| | Others | - 1UID, 1 SATA DOM power connector
| | | |
| | PCI-Express | - 1U Left Side:
1 (x8) PCI-Express & UIO Slots - 2U Left Side:
3 (x8) PCI-Express & UIO Slots - 2U Right Side:
1 (x8) PCI-Express &
1 (x4) PCI-Express Slots | | IPMI | | | | | |
| | 1U Chassis | * Please use air-shroud
MCP-310-00026-01
(Air-shrouds sold separately) | | 2U Chassis | * Please use air-shroud
MCP-310-00025-01
(Air-shrouds sold separately) | | Important Chassis Notes | - To ensure system stability, a 420W (minimum) ATX power supply
[ 4-pin (+12V), 8-pin (+12V) and 20-pin are required] | | | |
| | BIOS Type | - 8Mb Flash EEPROM with AMI® BIOS
| | BIOS Features | - Plug and Play (PnP)
- APM 1.2
- DMI 2.3
- PCI 2.2
- ACPI 2.0
- BIOS Rescue Hot Keys
- USB Keyboard Support
- Hardware BIOS Virus Protection
- SMBIOS 2.3
| | | |
| | Software | - Optional IPMI (Intelligent Platform Management Interface) 2.0
- Super
 Doctor III - Watch Dog
| | Power Configurations | - ACPI Power Management
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Keyboard Wakeup from Soft-Off
- CPU Fan auto-off in sleep mode
- Power-on mode control for AC power loss recovery
- Internal/External modem remote ring-on
| | | |
| | CPU | - Monitors CPU Core Voltages, +3.3V, +5V, ±12V, +5V Standby, HyperTransport Link voltage, memory voltage, VBAT, Chipset voltage
- CPU switching voltage regulator
| | FAN | - Total up to 8-fan status tachometer monitoring
- Up to two 4-pin and six 3-pin fan headers
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
| | Temperature | - Monitoring for CPU and chassis environment
- CPU Thermal Trip Support
- Thermal Control for 8x Fan Connectors
- I2C Temperature Sensing Logic
| | LED | - CPU / System Overheat LED
- Suspend-State Indicator LED
- +5V Standby Alert LED
- UID/Remote LED
| | Other Features | - Chassis Intrusion Detection
- Chassis Intrusion Header
| | | | RoHS
|
 | | Environmental Specifications | - Operating Temperature:
10°C to 35°C (50°F to 95°F) - Non-operating Temperature:
-40°C to 70°C (-40°F to 158°F) - Operating Relative Humidity:
8% to 90% (non-condensing) - Non-operating Relative Humidity:
5% to 95% (non-condensing) | | | |
| | FCC | - Passed to meet FCC standard requirement
| |
