 | |
 | | SYS-1026GT-TF | - SuperServer 1026GT-TF (Black)
| | | | | CPU | - Dual 1366-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Intel® Xeon® Processor X5600/E5600/L5600 Series
(Westmere) 40W - 95W
- Intel® Xeon® Processor X5500/E5500/L5500 Series
(Nehalem-EP) 38W - 95W
| | QPI | | | | | | Memory Capacity | - 12x 240-pin DIMM slots
- Supports up to 192 GB 1333 / 1066 / 800MHz DDR3 ECC Registered memory
- Supports up to 48 GB 1333 / 1066 / 800MHz DDR3 ECC / Non ECC Unbuffered memory
- Memory Mirroring supported
| | Memory Type | - 1333 / 1066 / 800MHz ECC Registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
| | DIMM Sizes | - 1GB, 2GB, 4GB , 8GB , 16GB
| | Memory Voltage | | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
| | | |
| | Chipset | - Intel® 5520 (Tylersburg) chipset
- ICH10R + IOH-36D
| | SATA | - Intel ICH10R SATA 3.0Gbps Controller
- RAID 0, 1, 5, 10 support
| | IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Nuvoton WPCM450 BMC
| | Network Controllers | - Intel® 82576 Dual-Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT 3 support for fast, scaleable, and reliable networking
- VMDq support for better performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
| | Graphics | | | Super I/O | | | Clock Generator | | | | |
| | Serial ATA | - Six Serial ATA ports
- Six SATA hard drives supported
| | LAN | - 2x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
| | USB | - 2 rear + 1 header (2 Ports)
- 4 total USB ports, 2.0 Compliant / 1.1 Compliant
| | VGA | | | Serial Port | - 1 Fast UART 16550 serial port
| | | | | BIOS Type | - 32Mb SPI Flash EEPROM with AMI® BIOS
| | BIOS Features | - Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
| | | | |
| | Form Factor | | | Model | | | | |
| | Height | | | Width | | | Depth | | | Gross Weight | | | Available Color | | | | |
| | Buttons | - Power On/Off button
- System Reset button
| | LEDs | - Power LED
- Hard drive activity LED
- 2x Network activity LEDs
- System Overheat LED / Fan fail LED /
UID LED | | | | | PCI-Express | | | | |
| | Hot-swap | - 6x 2.5" Hot-swap SATA drive bays
| | | |
| SAS/SATA HDD Backplane
(SAS support requires optional SAS controller) | | | | |
| | Fans | - 8x 4cm heavy-duty counter-rotating PWM fans with optimal fan speed control
| | | |
| | 1400W high-efficiency power supply with PMBus | | AC Input | - 1200W: 100 - 140V, 50 - 60Hz, 10.5 - 14.7 Amp
- 1400W: 180 - 240V, 50 - 60Hz, 7.2 - 9.5 Amp
| DC Output
+5V standby | | DC Output
+12V | - 100 Amp @ 100-140V
- 117 Amp @ 180-240V
| | With Power Distributor | | | Certification | 
Gold Certified
[ Test Report ] | | | |
| | CPU | - Monitors for CPU Cores,+1.5V, +3.3V, +5V, +12V, +5 Stdby, +3.3 Stdby, VBAT, Memory Voltages.
- CPU Core 6-Phase-switching voltage regulator
| | FAN | - Total of four 4-pin PWM fans
- 4x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 4x Fan Connectors
- PSU I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
| | LED | - Power Fail / Overheat LED
- Suspend-state Indicator LED
- UID LED
| | Other Features | | | | |
| RoHS
| | | Environmental Spec. | - Operating Temperature: 10° to 35° C (50° to 95°F)
- Non-operating Temperature: -40° to 70° C (-40° to 158° F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
| |
