 | |
 | | MBD-X9DB3-TPF -O | - X9DB3-TPF (Standard Retail Pack)
| | MBD-X9DB3-TPF -B | | | | |
| | Dimensions | - 12.3" x 13" (31.24cm x 33.02cm)
| | | | | CPU | - Intel® Xeon® processor E5-2400 and E5-2400 v2 (up to 95W TDP **)
- Dual Socket B2 (LGA 1356)
| | Cache | | | System Bus | | | ** Motherboard supports this maximum TDP. Please verify your system can thermally support | | | | | Memory Capacity | - 12x 240-pin DDR3 DIMM slots
- Up to 768GB DDR3 ECC LRDIMM
- Up to 384GB DDR3 ECC Registered memory (RDIMM)
- Up to 96GB DDR3 ECC/non-ECC Un-Buffered memory (UDIMM)
| | Memory Type | - 1600/1333/1066/800MHz* ECC DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
- Support ECC and non-ECC UDIMMs
* Maximum memory speed may be capped by CPU. Please verify that the chosen CPU can support desired memory speed. | | DIMM Sizes | - 32GB, 16GB, 8GB, 4GB, 2GB, 1GB,
64GB LRDIMM | | Memory Voltage | | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
| | | | | Chipset | | | SATA | - SATA 2.0 3Gb/s with RAID 0, 1, 5, 10
- SATA 3.0 6Gb/s with RAID 0, 1, 5, 10
| | SAS | - SAS from C606
- RAID 0, 1, 10 support
| | IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Nuvoton WPCM450 BMC
| | Network Controllers | - Intel® 82599EN Single Port 10G SFP+
- Intel® i210 Dual Port Gigabit Ethernet
- Virtual Machine Device Queues reduce I/O overhead
- Supports 10G SFP+, 100BASE-TX, and 1000BASE-T, RJ45 output
- 1x Realtek RTL8201F PHY (dedicated IPMI)
(Both CPUs need to be installed for 10Gb LAN port to be enabled) | | Video | | | | | | SATA | - 2 SATA 3.0 ports (6Gb/s)
- 4 SATA 2.0 ports (3Gb/s)
| | SAS | | | LAN | - 1 SFP+ 10GbE LAN port
- 2 RJ45 Gigabit Ethernet LAN ports
- 1 RJ45 Dedicated IPMI LAN port
| | USB | - 8 USB 2.0 ports total
(2 rear + 4 via header + 2 Type A) | | Video | | | Serial Port / Header | - 2 Fast UART 16550 ports: 1 rear, 1 header
| | DOM | - 1 DOM (Disk on Module) power connector
| | TPM | | | | | |
| | 2U Chassis | | | 3U Chassis | | | Important Chassis Notes | - To support the new generation Intel® Xeon® processor-based motherboards, Revision M chassis is recommended. Please talk to your sales representative for details.
| |
| | |
| | PCI-Express | - 1x PCI-E 3.0 x16
- 2x PCI-E 3.0 x8
- 1x PCI-E 3.0 x4 (in x8)
- 1x PCI-E 2.0 x4 (in x8)
- 1x PCI-32 Legacy
(Both CPUs need to be installed for full access to PCI-E slots and onboard controllers. See manual block diagram for details.) | | | | | BIOS Type | - 128Mb SPI Flash EEPROM with AMI BIOS
| | BIOS Features | - Plug and Play (PnP)
- APM 1.2
- PCI 2.3
- ACPI 1.0 / 2.0 / 3.0 / 4.0
- USB Keyboard support
- SMBIOS 2.7.1
- UEFI 2.3.1
| | | | | Software | | | Power Configurations | - ACPI / APM Power Management
- Power-on mode for AC power recovery
| | | | | Voltage | - Monitors for CPU Cores, +1.1V, +1.5V, +3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, Memory Voltages.
- 5+1 Phase-switching voltage regulator
| | FAN | - Eight 4-pin fan headers with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x Fan Connectors
- Thermal Monitor 2 (TM2) support
- PECI
| | LED | - CPU / System Overheat LED
- Suspend static indicator LED
- UID/Remote UID
| | Other Features | - Chassis intrusion detection
- Chassis intrusion header
- RoHS
- Dual Cooling Zones
| | | | |
| | Operating Temperature Range | - 10°C - 35°C (50°F - 95°F)
| | Non-Operating Temperature Range | - -40°C - 70°C (-40°F - 158°F)
| | Operating Relative Humidity Range | - 8% - 90% (non-condensing)
| | Non-Operating Relative Humidity Range | - 5% - 95% (non-condensing)
| |
