 |
|
 |
| MBD-PDSMi-LN4+-O |
- PDSMi-LN4+ (Standard Retail Pack)
|
| MBD-PDSMi-LN4+-B |
|
| |
|
|
| Form Factor |
|
| Dimensions |
- 12.0" width x 9.6 " length , (30.5cm x 24.4cm), 6 layers
|
| |
|
| CPU |
- Single LGA775 ZIF Socket
- Supports a Quad-Core Intel® Xeon® 3200 series processor
- Supports a Dual-Core Intel® Xeon® 3000 series processor
- Supports a Quad-Core Intel® Core™2 Extreme series processor
- Supports an Intel® Core™2 Quad series processor
- Supports an Intel® Core™2 Duo series processor
- Supports an Intel® Pentium® processor E2000 series
- Supports a Dual-Core Intel® Pentium® D processor
- Supports an Intel® Pentium® Extreme Edition processor
- Supports an Intel® Pentium® 4 processor
- Supports an Intel® Celeron® processor E1000 series
- Supports an Intel® Celeron® processor 400 series
- NOTE: This board DOES NOT support Q9000, E8000, E7000, E5000 series or 45nm processor
|
| System Bus |
- 1066 / 800 / 533 MHz system bus
|
| |
|
|
| Memory Capacity |
- Four 240-pin DIMM sockets
- Supports up to 8 GB of unbuffered ECC / non-ECC DDR2 667/533MHz memory (Dual Channel)
|
| Memory Type |
- DDR2 667/533MHz unbuffered ECC / non-ECC SDRAM, 240-pin gold-plated DIMMs
|
| DIMM Sizes |
- 256 MB, 512 MB, 1 GB, 2GB
|
| Memory Voltage |
|
| |
|
|
| Chipset |
- Intel 3000 (Mukilteo-2) chipset
- ICH7R + PXH-V + Intel® 82573V + Intel® 82573L
|
| Serial ATA |
- Intel® ICH7R SATA2 (3 Gbps) controller built-in
- Intel:
RAID 0, 1, 5, 10 support (Windows Only)
- Adaptec:
RAID 0 (Two, three, four drives only)
RAID 1 (Two hard drives only)
|
| IPMI |
|
| Network Controllers |
- Dual double-stack ports using 1x Intel® 82573V and 3x Intel® 82573L Gigabit PCI-Express Ethernet Controllers, Four ports total
- Supports 10Base-T, 100Base-TX, 1000BASE-TX, RJ45 output
|
| VGA |
- On-board XGI Volari Z7 graphics
|
| Super I/O |
|
| Clock Generator |
|
| |
|
|
| Serial ATA |
- Four Serial ATA ports (3 Gbps performance)
- Four SATA hard drives supported
|
| IDE |
- One EIDE channel supports up to two UDMA IDE devices
- IDE Master / Slave 2 ports
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
- White Connector for Compact Flash (CF, 40-pin IDE connector) card only
|
| Floppy |
- 1 Floppy controller; 1.44 MB
|
| LAN |
|
| USB |
- USB 2.0 compliant / 1.1 compatible
- 4x internal USB headers
- 2x rear ports
|
| VGA |
|
| Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
| Serial Ports |
- 1x Fast UART 16550 serial port
- 1x Header
|
| Parallel Port |
- 1x ECP / EEP Parallel Header
|
|
|
|
|
|
| 4U / Tower |
|
| Important Note |
- To ensure system stability, a ATX power supply w/ 4A (minimum) on 5V Standby is required
- Only this Supermicro 1U chassis is recommended for this Network Building Block Solution
|
| |
|
|
| PCI-X |
- 1x 64-bit PCI-X 133MHz slot
|
| PCI |
- 1x 32-bit 33MHz PCI (5V) slot
|
| Note |
- Riser Card required for 1U systems
|
| |
|
|
| BIOS Type |
- 8Mb Flash EEPROM with Phoenix BIOS®
|
| BIOS Features |
- Plug and Play (PnP)
- DMI 2.3 support
- PCI 2.2
- ACPI 1.0
- SMBIOS 2.3
- USB Keyboard support
|
| |
|
|
| Software |
- Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
- W83793 H/W Monitor
|
| Power Configurations |
- ACPI/APM Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode control for AC power loss recovery
- Internal / External Modem Rign-on
|
| |
|
|
| Voltage |
- Monitors for CPU Cores, +1.5V, +3.3V, +5, ±12V, +5V Standby
- CPU Core 3-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
- Adjustable CPU clock frequency ratio
|
| FAN |
- Fan Speed Control
- 6x 4-pin fan headers
- 6x fans with tachometer monitoring
- Status monitor with firmware speed control
- Low noise fan speed control
- Status monitor for on/off control
- Support 3-pin fans (without speed control)
- Pulse Width Modulated (PWM) fan connector
|
| Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Monitor 2 (TM2) support
- PECI
|
| LED |
- CPU / System Overheat LED
- Standby Power alert LED
|
| Other Features |
- Chassis Intrusion Detection
- Chassis Intrusion Header
|
| |
|
|
RoHS
|
|
| Environmental Spec. |
- Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
| |
|
|
| FCC |
- Passed to meet FCC standard requirement
|
|
