 | |
 | | MBD-PDSML-LN2+-O | - PDSML-LN2+ (Standard Retail Pack)
| | MBD-PDSML-LN2+-B | | | | |
| | Form Factor | | | Dimensions | - 9.6" width x 9.6 " length , (24.4cm x 24.4cm), 6 layers
| | | | | CPU | - Single LGA775 ZIF Socket
- Supports a Quad-Core Intel® Xeon® 3200 series processor
- Supports a Dual-Core Intel® Xeon® 3000 series processor
- Supports a Quad-Core Intel® Core™2 Extreme series processor
- Supports an Intel® Core™2 Quad series processor
- Supports an Intel® Core™2 Duo series processor
- Supports an Intel® Pentium® processor E2000 series
- Supports a Dual-Core Intel® Pentium® D processor
- Supports an Intel® Pentium® Extreme Edition processor
- Supports an Intel® Pentium® 4 processor
- Supports an Intel® Celeron® processor E1000 series
- Supports an Intel® Celeron® processor 400 series
- NOTE: This board DOES NOT support Q9000, E8000, E7000, E5000 series or 45nm processor
| | System Bus | - 1066 / 800 / 533 MHz system bus
| | | |
| | Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 8 GB of unbuffered ECC / non-ECC DDR2 667/533MHz memory (Dual Channel)
| | Memory Type | - DDR2 667/533MHz unbuffered ECC / non-ECC SDRAM, 240-pin gold-plated DIMMs
| | DIMM Sizes | - 256 MB, 512 MB, 1 GB, 2GB
| | Memory Voltage | | | | |
| | Chipset | - Intel 3000 (Mukilteo-2) chipset
- ICH7R + Intel® 82573V + Intel® 82573L
| | Serial ATA | - Intel® ICH7R SATA2 (3 Gbps) controller built-in
- Intel:
RAID 0, 1, 5, 10 support (Windows Only) | | IPMI | | | Network Controllers | - 1x Intel® 82573V Gigabit PCI-Express Ethernet
- 1x Intel® 82573L Gigabit PCI-Express Ethernet
- Supports 10Base-T, 100Base-TX, 1000BASE-TX, RJ45 output
| | VGA | - On-board XGI Volari Z7 graphics
| | Super I/O | | | Clock Generator | | | | |
| | Serial ATA | - Four Serial ATA ports (3 Gbps performance)
- Four SATA hard drives supported
| | IDE | - One EIDE channel supports up to two UDMA IDE devices
| | Floppy | - 1 Floppy controller; 1.44 MB
| | LAN | | | USB | - 6x USB 2.0 compliant / 1.1 compatible
- 4x internal USB headers
- 2x rear ports
| | VGA | | | Keyboard / Mouse | - PS/2 keyboard and mouse ports
| | Serial Ports | - 1x Fast UART 16550 serial port
- 1x Header
| | | | |
| | 1U Chassis | | | 2U Chassis | | | Mid-Tower | | | Tower / 4U Rackmount | | | Important Note | - To ensure system stability, a 300W (minimum) ATX power supply [4-pin +12V AND (20 or 24-pin)] is recommended.
| | | |
| | Universal Slot | - 1 (x8) PCI-Express Slot OR
- 1x 32-bit 33MHz PCI Slot
| | PCI-Express | - 1 (x4) PCI-e (using x8) slot
| | PCI | - 1x 32-bit 33MHz PCI (5V) slot
| | | |
| | BIOS Type | - 8Mb Flash EEPROM with Phoenix BIOS®
| | BIOS Features | - Plug and Play (PnP)
- DMI 2.3 support
- PCI 2.2
- ACPI 1.0
- ACPI 1.0 (limited)
- USB Keyboard support
- SMBIOS 2.3
| | | |
| | Software | - Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
- W83793 H/W Monitor
| | Power Configurations | - ACPI/APM Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode control for AC power loss recovery
- Internal / External Modem Rign-on
| | | |
| | Voltage | - Monitors for CPU Cores +1.8V, +3.3V, +5V, ±12V, +5V Standby
- CPU 3-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
| | FAN | - Total of six 4-pin fan headers
- 6 fans with tachometer monitoring
- Status monitor with firmware speed control
- Low noise fan speed control
- Status monitor for on/off control
- Support 3-pin fans (without speed control)
- Pulse Width Modulated (PWM) fan connector
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Monitor 2 (TM2) support
- PECI
| | LED | - CPU / System Overheat LED
- Standby Power alert LED
| | Other Features | - Chassis Intrusion Detection
- Chassis Intrusion Header
| | | |
| | Environmental Spec. | - Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
| | | |
| | FCC | - Passed to meet FCC standard requirement
| |
