 | |
 | | MBD-X7DCL-3 -O | - X7DCL-3 (Standard Retail Pack)
| | MBD-X7DCL-3 -B | | | | |
| | Form Factor | | | Dimensions | - 12.05" x 10" (30.6cm x 25.4cm)
| | | |
| | CPU | - Dual 771-pin LGA Sockets
- Supports up to Dual Intel® 64-bit Xeon®processor(s) of the same type below:
- Quad-Core Intel®
Xeon®Processor
5400/5300 sequence (Harpertown
/Clovertown processor)
up to 3.16 GHz - Dual-Core Intel®
Xeon®Processor
5200/5100 sequence (Wolfdale/Woodcrest processor) up to 3.40 GHz | System Bus | - 1333 / 1066 MHz system bus
| | Operating System Software | - Supports 64-bit Operating Systems
- Supports 32-bit Operating Systems
| | | |
| | Memory Capacity | - Six 240-pin DIMM sockets
- Supports up to 48GB 667/ 533MHz DDR2 ECC Register Single/Dual Rank memory *
- Dual channel memory bus
- Memory must be populated in pairs
| | Memory Type | - 667/533MHz Register DDR2 ECC Single/Dual Rank SDRAM 72-bit, 240-pin gold-plated DIMMs *
| | DIMM Sizes | - 256MB, 512MB, 1GB, 2GB, 4GB, 8GB**
| | Memory Voltage | | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
| | | |
| | Chipset | - Intel® 5100 (San Clemente) chipset
- Intel® ICH9R
| | SAS | - Broadcom SAS1068E
- RAID 0, 1, 10 support
- (Optional: AOC-IButton68) RAID 5 support
| | SATA | - Intel ICH9R SB SATAII Controller
- RAID 0, 1, 5, 10 support (Windows only)
- RAID 0, 1, 10 support (Linux)
| | IPMI | - Support for Intelligent Platform Management Interface v.2.0 / 1.5
- 200-pin IPMI slot (SIMLC)
- (Optional: AOC-SIMLC)
- NOTE: KVM-over-LAN supported w/ AOC-SIM1U+ - PCB 1.1A only
| | Network Controllers | - Intel® 82573V & 82573L Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
| | Graphics | - XGI Z9 with 32 MB of video memory
| | Super I/O | | | Clock Generator | | | | |
| | SAS | | | Serial ATA | - Six Serial ATA ports
- Six SATA hard drives supported
| | IDE | - Single EIDE channel supports up to two UDMA IDE devices(IDE-M, IDE-S) including CF card
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
- Compact Flash (40-pin connector, IDE 1, single channel) slot
| | Floppy | - 1 Floppy controller; 1.44 MB, 2.88 MB
| | LAN | | | USB | - 2x USB rear ports
- 3x USB internal header
- 5 total USB ports, 2.0 Compliant / 1.1 Compliant
| | VGA | | | Keyboard / Mouse | - PS/2 keyboard and mouse ports
| | Serial Port / Header | - 1 Fast UART 16550 serial port
- 1 Header
| | | | |
| | 1U Chassis | - CSE-813MTQ-520C
- CSE-813MTQ-280C
- CSE-813MT-420C
- CSE-813MT-410C
| | 2U Chassis | - CSE-823TQ-550LP
- CSE-823T-550LP
- CSE-823MTQ-R700LP
- CSE-825TQ-560LP
- CSE-825MTQ-R700LP
| | Mid Tower | - CSE-733TQ-645
- CSE-733TQ-465
| | Tower / 4U Rackmount | | | Important Chassis Notes | - To ensure system stability, a 500W (minimum) ATX power supply
[8-pin (+12V) and 24-pin are required] | | | |
| | PCI-Express | - 2 (x8) PCI-e slots
- 1 (x4) PCI-e (using x8) slot
| | PCI | | | | |
| | BIOS Type | - 8Mb Flash EEPROM with Phoenix ® BIOS
| | BIOS Features | - Plug and Play (PnP)
- DMI 2.3
- PCI 2.2
- ACPI 1.0/2.0/3.0
- USB Keyboard support
- Hardware BIOS Virus protection
- SMBIOS 2.5
| | | |
| | Software | - Optional IPMI (Intelligent Platform Management Interface) v1.5 / 2.0
- SuperDoctor® III
- Watch Dog
- NMI
| | Power Configurations | - ACPI Power Management
- Main Switch Override Mechansim
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode for AC power recovery
- Internal/External modem remote ring-on
| | | |
| | Voltage | - Monitors for CPU Cores,+1.8V, +3.3V, +5V, ±12V, +3.3V Stdby, +5 Stdby, VBAT, HT, Memory, Chipset
- CPU Core 6-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
| | FAN | - Total of six 4-pin fans
- 6x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Support for 3-pins (w/o speed control)
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 6x Fan Connectors
- PSU I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
| | LED | - CPU / System Overheat LED
- Suspend-state Indicator LED
| | Other Features | - Chassis intrusion detection
- Chassis intrusion header
- Chipkill Support
| | | |
| | Environmental Spec. | - Operating Temperature: 10° to 35°C (50° to 95°F)
- Non-operating Temperature: -40° to 70°C (-40° to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
| |
