 | |
 | | MBD-X7SLM-O | - X7SLM (Standard Retail Pack)
| | MBD-X7SLM-B | | | | | | Form Factor | | | Dimensions | - 9.6" x 9.6 ", (24.4cm x 24.4cm)
| | | | | CPU | - Single LGA775 ZIF Socket
- Supports an Intel® Core™2 Duo E4000 Series
- Supports an Intel® Pentium® E2000 Series
- Supports an Intel® Pentium® D 945, 935, 925, 915 and 820, 805
- Supports an Intel® Pentium® 4 600 and 500 Series
- Supports an Intel® Celeron® E1000 Series
- Supports an Intel® Celeron® 400 Series
- Supports an Intel® Celeron® D 300 Series
| | System Bus | - 1066 / 800 / 533 MHz system bus
| | | | | Memory Capacity | - Two 240-pin DIMM slots
- Supports up to 2 GB of unbuffered, non-ECC DDR2 667/533/400MHz memory (Single / Dual Channel)
| | Memory Type | - DDR2 667/533/400MHz unbuffered, non-ECC SDRAM, 240-pin gold-plated DIMMs
| | DIMM Sizes | | | Memory Voltage | | | | | | Chipset | - Intel 945GC
- ICH7 + Realtek RTL8111C
| | Serial ATA | - Intel® ICH7 SATA2 (3 Gbps) controller built-in
| | Network Controllers | - 2x Realtek RTL8111C Gigabit Ethernet
- Supports 10BASE-T, 100/1000BASE-TX, RJ45 output
| | Graphics | | | Super I/O | | | Clock Generator | | | | | | Serial ATA | - Four Serial ATA ports ( 3Gb/s )
- Four SATA hard drives supported
| | IDE | - One EIDE channel supports up to two UDMA IDE devices
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
| | Floppy | - 1 Floppy controller; 1.44 MB
| | LAN | | | USB | - 5x USB 2.0 / 1.1 compatible
- 2 rear + 1 TypeA connector + 1 header (2 ports)
| | VGA | | | Keyboard / Mouse | - PS/2 keyboard and mouse ports
| | Serial Ports | - 1x Fast UART 16550 serial port
- 1x Serial Header
| | | | | | 1U | | | Important Note | - Only Supermicro 1U chassis is recommended for 1U Building Block Solutions
| | | | | PCI-Express | | | PCI | - 1x 32-bit 33MHz PCI (5V) slots
| | | | | BIOS Type | - 8Mb Flash EEPROM with AMI BIOS
| | BIOS Features | - Plug and Play (PnP)
- APM 1.2
- DMI 2.3
- PCI 2.2
- ACPI 1.0 / 2.0 / 3.0
- USB Keyboard support
- Hardware BIOS Virus protection
- SMBIOS 2.3
| | | | | Software | | | Power Configurations | - ACPI/APM Power Management
- Main Switch Override Mechanism
- Suspend to RAM (STR)
- Power-on mode control for AC power recovery
- Internal / External modem remote ring-on
| | | | | Voltage | - Monitors for CPU Cores, +3.3V, +5V, +12V, +3.3V/+5V Standby, VBAT, Memory, Chipset
- CPU Core 3-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
| | FAN | - Total of five 4-pin fan headers
- 5 x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on / off control
- Support 3-pin fans (without speed control)
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan conn.
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 5 x Fan Connectors
- I2C temperature sensing logic
- Thermal Monitor 2 (TM2) Support
- PECI
| | LED | - CPU / System Overheat LED
- Suspend-state indicator LED
- +5V standby alert LED
| | Other Features | - Chassis intrusion Detection
- Chassis intrusion Header
- SDDC Support
| | | |
| | Environmental Spec. | - Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
| | | |
| | FCC | - Passed to meet FCC standard requirement
| |
