| | MBD-X7DA3+-O | - X7DA3+ (Standard Retail Pack)
| MBD-X7DA3+-B | | | | Form Factor | | Dimensions | - 12.075" x 13.05" (30.7cm x 33.2cm)
| | | CPU | - Dual 771-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same
type below: - Quad-Core Intel®
Xeon®Processor 5400/5300 sequence (Harpertown /Clovertown processor) up to 3.16 GHz - Dual-Core Intel®
Xeon®Processor 5200/5100/5000 sequence (Wolfdale /Woodcrest/Dempsey processor) up to 3.40 GHz | System Bus | - 1333 / 1066 / 667 MHz system bus
| Operating System Software | - Supports 64-bit Operating Systems
- Supports 32-bit Operating Systems
| | | Memory Capacity | - Eight 240-pin DIMM sockets
- Supports up to 32 GB 667 / 533MHz DDR2 ECC FB-DIMM memory
- Dual branch memory bus
- Memory must be populated in pairs
- Memory Mirroring supported
| Memory Type | - 667 / 533MHz FB-DIMM (Fully Buffered DIMM) DDR2 ECC SDRAM 72-bit, 240-pin gold-plated DIMMs
| DIMM Sizes | | Memory Voltage | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
| | | Chipset | - Intel® 5000X (GreenCreek) chipset
- MCH + PXH-V + ESB2
| SAS | - Adaptec AIC-9410W Serial-Attached SCSI (SAS) Controller
- SAS Dual-Channel (internal)
- Each SAS channel supports up to 4 SAS / SATA drives for a total of up to 8 SAS or SATA hard drives
- Host RAID 0, 1, & 10 support
| SATA | - Intel ESB2 SATAII Controller
- RAID 0, 1, 5, 10 support (Windows Only)
- RAID 0, 1, 10 support (Linux)
| RAID | - Support for Zero-Channel RAID
- SAS RAID 0, 1, 5, 10
- Optional: (Card NOT included)
| IPMI | - Support for Intelligent Platform Management Interface v.2.0
- 200-pin IPMI slot (SIMLP)
- (Optional: AOC-SIMLP-B)
- (Optional: AOC-SIMLP-3) with 3rd LAN support
- NOTE: KVM-over-LAN not supported - there is no DVO signal to the IPMI slot
| Network Controllers | - Intel® 82563EB Dual-Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT support for fast, scaleable, and reliable networking
| Super I/O | | | | Serial ATA | - Six Serial ATA ports
- Six SATA hard drives supported
| IDE | - Single EIDE channel supports up to two UDMA IDE devices(IDE-M, IDE-S) including CF card
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
- Compact Flash (40-pin connector, IDE 1, single channel) slot
| Floppy | - 1 Floppy controller; 1.44 MB, 2.88 MB
| LAN | | USB | - 4x USB rear ports
- 2x USB internal header
- 6 total USB ports, 2.0 Compliant / 1.1 Compliant
| Audio | - 7.1 High Definition audio
| Keyboard / Mouse | - PS/2 keyboard and mouse ports
| Serial Port / Header | - 1 Fast UART 16550 serial port
| Parallel Port | - 1 ECP / EEP parallel port
| | | | | 2U Chassis | | 3U Chassis | | Tower / 4U Rackmount | | Important Chassis Notes | - To ensure system stability, a 500W (minimum) ATX power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin are required] | | | PCI-Express | - 1 (x16) PCI-e slot
- 1 (x4) PCI-e (using x16) slot
| PCI-X | - 2x 64-bit 133/100MHz PCI-X (3.3V) slots
- 1x 64-bit 100MHz PCI-X (3.3V) slot
| PCI | - 1x 32-bit 33MHz PCI (5V) slot
| | | BIOS Type | - 8Mb Flash EEPROM with Phoenix® BIOS
| BIOS Features | - Plug and Play (PnP)
- SMBIOS 2.3
- DMI 2.3
- PCI 2.2
- ACPI 1.0
- PCI-X 1.0
- USB Keyboard support
- Hardware BIOS Virus protection
| | | Software | - Optional IPMI (Intelligent Platform Management Interface) v2.0
- SuperDoctor® III
- Watch Dog
- NMI
| Power Configurations | - ACPI Power Management
- Main Switch Override Mechansim
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Keyboard Wakeup from Soft-Off
- CPU Fan Auto-off in Sleep Mode
- Power-on mode for AC power recovery
- Internal/External modem remote ring-on
- Suspend to RAM (STR)
| | | Voltage | - Monitors for CPU Cores, +1.8V, +3.3V, +5V, -12V & +5V Standby, VBAT
- CPU Core 5-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
| FAN | - Total of eight 4-pin fans
- 8x fans with status monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Support for 3-pins (w/o speed control)
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
| Temperature | - Monitoring for CPU and chassis, environment
- CPU thermal trip support
- Thermal Control for 8x Fan Connectors
- PSU I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
| LED | - CPU / System Overheat LED
- Suspend-state Indicator LED
- +5V Standby Alert LED
| Other Features | - Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
| | Environmental Spec. | - Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
| | | FCC | | |