| | MBD-PDSME+-O | - PDSME+ (Standard Retail Pack)
| MBD-PDSME+-B | | | | Form Factor | | Dimensions | - 12" x 9.6", (30.5cm x 24.4 cm)
| | | CPU | - Single LGA775 ZIF Socket
- Supports a Quad-Core Intel® Xeon® 3200 series processor
- Supports a Dual-Core Intel® Xeon® 3000 series processor
- Supports a Quad-Core Intel® Core™2 Extreme series processor
- Supports an Intel® Core™2 Quad series processor
- Supports an Intel® Core™2 Duo series processor
- Supports an Intel® Pentium® processor E2000 series
- Supports a Dual-Core Intel® Pentium® D processor
- Supports an Intel® Pentium® Extreme Edition processor
- Supports an Intel® Pentium® 4 processor
- Supports an Intel® Celeron® processor E1000 series
- Supports an Intel® Celeron® processor 400 series
- NOTE: This board DOES NOT support Q9000, E8000, E7000, E5000 series or 45nm processor
| System Bus | - 1066 / 800 / 533 MHz system bus
| | | Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 8 GB of memory (Single / Dual Channel)
| Memory Type | - DDR2 667/533MHz unbuffered, ECC / non-ECC SDRAM, 240-pin gold-plated DIMMs
| DIMM Sizes | - 256 MB, 512 MB, 1 GB, 2GB
| Memory Voltage | | | | Chipset | - Intel 3010 (Mukilteo-2P) chipset
- ICH7R + PXH + Intel® 82573V + Intel® 82573L
| Serial ATA | - Intel® ICH7R SATA2 (3 Gbps) controller built-in
- Intel:
RAID 0, 1, 5, 10 support (Windows Only) - Adaptec:
RAID 0 (Two, three, four drives only) RAID 1 (Two hard drives only) | IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN & optional KVM-over-LAN support
- Supermicro Intelligement Management
- (Optional: AOC-SIM1U+)
- NOTE: Must use dedicated LAN for IPMI function
| Network Controllers | - 2x Single-port Gigabit PCI-Express Ethernet Controllers
- Intel® 82573V
- Supports 10BASE-T, 100BASE-T, 1000BASE-T, RJ45 output
| VGA | - On-board ATI ES1000 (16MB) graphics
| Super I/O | | Clock Generator | | | | Serial ATA | - Four Serial ATA ports (3 Gbps performance)
- Four SATA hard drives supported
| IDE | - One EIDE channel supports up to two UDMA IDE devices
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
| Floppy | - 1 Floppy controller; 1.44 MB
| LAN | | USB | - Up to 4x USB 2.0 / 1.1 compliant ports
- 2 rear ports
- 1 internal header for 2 ports
| VGA | | Keyboard / Mouse | - PS/2 keyboard and mouse ports
| Serial Ports | - 1x Fast UART 16550 serial port
- 1x internal header
| | | | | 2U | | Tower / 4U Rackmount | | Mid-Tower | | Important Note | - For a general system, a 400W (minimum) ATX12V power supply [8-pin +12V AND 24-pin is recommended to assure system stability].
| | | PCI-Express | - 1 (x4) PCI-e slot
- 1 (x8) PCI-e slot
| PCI - X | - 2x 64-bit 133MHz PCI-X (3.3V) slots
- 2x 64-bit 100MHz PCI-X (3.3V) slots
| | | BIOS Type | - 8Mb Flash EEPROM with Phoenix BIOS®
| BIOS Features | - Plug and Play (PnP)
- DMI 2.3 support
- PCI 2.2
- ACPI 1.0
- SMBIOS 2.3
- USB Keyboard support
| | | Software | - Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
| Power Configurations | - ACPI Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Keyboard Wakeup from Soft-Off
- CPU Fan auto-off in sleep mode
- Power-on mode control for AC power loss recovery
- Internal/External modem remote ring-on
- Suspend to RAM (STR)
| | | Voltage | - Monitors for CPU Cores (+1.5V, +1.8V, +3.3V, +5, ±12V, +5V Standby, VBAT)
- CPU Core 3-Phase-switching voltage regulator with auto-sense from 0.3750V-1.6000V
| FAN | - Total of six 4-pin fan headers
- 6x fans with tachometer monitoring
- Status monitor with firmware / software speed control
- Status monitor for on/off control
- Support 3-pin fans (with speed control)
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connector
| Temperature | - Monitoring for CPU and chassis environment
- CPU Thermal Trip support
- Thermal Monitor (TM2) Support
| LED | - CPU / System Overheat LED
- Standby alert LED
- Suspend-state indicator LED
| Other Features | - Chassis intrusion detection
- Chassis intrusion header
| | | Environmental Spec. | - Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
| | | FCC | - Passed to meet FCC standard requirement
| |