| | MBD-PDSBA+-O | - PDSBA+ (Standard Retail Pack)
| MBD-PDSBA+-B | | | | Form Factor | | Dimensions | - 11.5" x 9.5 ", (29.2cm x 24.0cm)
| | | CPU | - Single LGA775 ZIF Socket
- Supports a Dual-Core Intel® Xeon® 3000 Series processor
- Supports an Intel® Core™2 Duo Series processor
- Supports a Dual-Core Intel® Pentium® D processor
- Supports an Intel® Pentium® 4 processor
- Supports an Intel® Celeron® D processor
- NOTE: This board DOES NOT support Q9000, E8000, E7000, E5000 series or 45nm processor
| System Bus | - 1066 / 800 / 533 MHz system bus
| | | Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 8 GB of unbuffered, non-ECC DDR2 800/667/533MHz memory (Single / Dual Channel)
| Memory Type | - DDR2 800/667/533MHz unbuffered, non-ECC SDRAM, 240-pin gold-plated DIMMs
| DIMM Sizes | - 256 MB, 512 MB, 1 GB, 2 GB
| Memory Voltage | | | | Chipset | - Intel G965
- ICH8 + Intel® 82573L
| Serial ATA | - Intel® ICH8 SATA (3Gbps) controller built-in
| Network Controllers | - Intel® 82573L (Single Port) Gigabit PCI-Express Ethernet
- Supports 10BASE-T, 100/1000BASE-TX, RJ45 output
| Graphics | - On-chip integrated gfx graphics core
| Audio | - Realtek high quality 7.1 channel audio
| Super I/O | - Winbond 83627HG chip, STM (Trust Platform Module) controller
| Clock Generator | | TPM | | | | Serial ATA | - Four Serial ATA ports (3Gbps)
- Four SATA hard drives supported
| IDE | - One EIDE channel supports up to two UDMA IDE devices
- IDE Master / Slave 2 ports
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
| Floppy | - 1 Floppy controller; 1.44 MB
| LAN | | USB | - 6x USB 2.0 compliant external ports
- 2x internal headers supporting up to 4 ports (USB 2.0 Compliant)
| VGA | | Audio | - 1x Line In / Front L & R / Center & Sub-Woofer/ Surround L & R / Side Surround L & R / Line Out / Microphone ports
| Keyboard / Mouse | - PS/2 keyboard and mouse ports
| Serial Ports | - 1x Fast UART 16550 serial port
- 1x Serial Header
| Parallel Port | - 1x ECP / EEP Parallel Port
| | | | | Mid-Tower | | Tower / 4U Rackmount | | Important Note | - To ensure system stability, a 450W (minimum) ATX power supply [4-pin +12V AND (20 or 24-pin)] is required.
| | | PCI-Express | - 1 (x16) PCI-e slot (intended for Graphics applications)
- 1 (x4) PCI-e slot (using a x8 physical slot)
- 1 (x1) PCI-e slot
| PCI | - 3x 32-bit 33MHz PCI (5V) slots
| | | BIOS Type | - 8Mb Flash EEPROM with Phoenix BIOS®
| BIOS Features | - Plug and Play (PnP)
- DMI 2.3 support
- PCI 2.2
- ACPI 1.0 (limited)
- USB Keyboard support
- SMBIOS 2.3
| | | Software | | Power Configurations | - ACPI Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Keyboard Wakeup from Soft-Off
- Suspend to RAM (STR)
- Power-on mode control for AC power loss recovery
- Internal/External modem remote ring-on
| | | Voltage | - Monitors for CPU Cores, +1.8V, +3.3V, +5V, ±12V, +3.3V/+5V Standby, VBAT
- CPU Core 3-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
- Adjustable CPU clock frequency ratio settings (via BIOS)
| FAN | - Total of three 4-pin fan headers
- 3x fans with tachometer monitoring
- Status monitor with firmware/software speed control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connector
| Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Monitor (TM2) Support
| LED | - CPU / System Overheat LED
- +3V standby alert LED
- Suspend-state indicator LED
| Other Features | - Chassis intrusion detection
- Chassis intrusion header
| | Environmental Spec. | - Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
| | | FCC | | |